Professional accreditations & supporting documents

Entered in the registry book of professionals as a Mechanical Engineer under Republic Act No. 8495, with the privilege to assume the title and practise the profession. This is the statutory practising licence and does not expire on the certificate; the associated professional identification card is renewed on the PRC cycle.

Awarded the status of ASEAN Engineer with the designatory letters ASEAN Eng., having satisfied the qualification requirements of the AFEO Governing Board. Provides mutual recognition of engineering competence across ASEAN member states.

Held for practice in the Kingdom of Saudi Arabia during the Samsung and McDermott engagements. Not renewed after leaving the Kingdom; listed here for completeness of the record rather than as a current registration. Reinstatement is available on application should a Saudi assignment require it.

Institute membership. This is a membership record rather than a certification; the PMP credential itself has not been awarded — see the training entry in section 3.

Degree conferred by the Board of Trustees on the recommendation of the University Faculty. Deregulated status — exempted from Special Order per CHED Memorandum No. 32, series of 2001. The document set comprises the Department of Foreign Affairs authentication certificate, the attestation stamps, the Commission on Higher Education certification of authenticity, and the diploma itself.

The academic transcript that accompanies this set has been withheld from publication: it carries date of birth, home address and next-of-kin details. It is supplied directly to an employer or verification agency on request.

Twelve postgraduate modules completed across construction management, contract administration, procurement, cost, quality, risk, safety and research methods. The university's certification records the date of graduation as not applicable — the coursework is complete and the units are earned, but the degree has not been conferred. It is stated that way here deliberately, and should not be read as a completed master's degree.

Attested for use in Qatar. The record carries a Hague Convention apostille issued by the Philippine Department of Foreign Affairs on 21 January 2026 and an attestation by the Ministry of Foreign Affairs, State of Qatar (No. 2026121000111/1) dated 28 January 2026.

A complete specialization rather than a set of unrelated short courses. It covers the hydraulics of piping systems under single- and two-phase gas and liquid flow, pipe design, flange types and classes, valve types and classes, pipe stress analysis, pipe supports, cross-country onshore pipeline construction, and ASME B31.1 Power Piping and ASME B31.3 Process Piping.

Directly adjacent to rotating-equipment work: suction and discharge line sizing, NPSH margin, two-phase line behaviour, nozzle loading and support design, and material selection against service conditions — the interfaces where pump and compressor packages meet the piping designer.

• Single-Phase Pipe Hydraulics and Pipe Sizing 5 Aug 2026 · CR5GL2T3BG4R PDF
• Two-Phase Pipe Hydraulics and Pipe Sizing 14 Aug 2026 · L0F9VBF8DPZM Verify ↗
• Pipe Material Specification 30 Aug 2026 · 0PKQZ6V589Q5 PDF
• ASME B31 Series and Pipeline Construction 4 Sep 2026 · 5HFR2LKXLOYX PDF

The individual Two-Phase course certificate is not held as a separate file. The specialization certificate names all four constituent courses, so it evidences that course directly; Coursera verification for it is linked above in any case.

Extends the discipline from process rotating equipment into building services: air conditioning fundamentals and cooling-load estimation, selecting and sizing the chillers, cooling towers, pumps and air handling units that meet the load, and the life-safety side that is sized by code rather than by comfort — ventilation rates, stairwell and lobby pressurization, and smoke extraction.

Three of the four are courses 1, 2 and 3 of L&T EduTech’s four-course Design of Ventilation & Air Conditioning System for Buildings specialization, which is in progress; the specialization itself is not claimed until all four are complete. HVAC Systems is a separate, standalone course from Interplay Learning.

• Basics of Air Conditioning & Heat Load Calculation L&T C1 · 11 Sep 2026 · MXRO9GXNX8CL PDF
• Ventilation, Life Safety & Smoke Extraction in Building L&T C2 · 11 Sep 2026 · L9HUBXH85TYZ PDF
• Air Conditioning Equipment Selection, Design and Sizing L&T C3 · 23 Sep 2026 · VV6MD9FFJNPQ PDF
• HVAC Systems Interplay Learning · 5 Sep 2026 · 9RF74IF1FHYT PDF

Carries the building-services work into fire protection: the fundamentals of fire detection, alarm and life-safety systems, then the water-based side — fire hydrant systems and the design of fire protection systems as a whole. It sits alongside the offshore fire fighting packages from the Manifa project and the fire-water demand calculations published on this site.

The three are courses 1, 2 and 3 of L&T EduTech’s four-course Fire and Life Safety Systems specialization. Course 4, Fire Detection & Fire Alarm Systems and Safety Signages, is under completion; the specialization itself is not claimed until all four are complete.

• Basics of Fire Protection, Detection & Life Safety Systems L&T C1 · 27 Sep 2026 · 3B4KRPOINRW4 PDF
• Fire Hydrant System L&T C2 · 28 Sep 2026 · 4MDFL5T475Z9 PDF
• Fire Protection System L&T C3 · 30 Sep 2026 · B7O0C1JAFXJH PDF
• Fire Detection & Fire Alarm Systems and Safety Signages L&T C4 Under completion

Certification awarded on satisfactory completion of the Intertek Business Assurance Lean Six Sigma Green Belt programme. The preparatory training that preceded it was delivered separately by RS Management in April 2017 and is listed below as its own record.

Awarded for having met all conditions and requirements established by ASEM. Lapsed and not renewed; recorded here so the professional history is complete.

Attained by demonstrating knowledge of green building practices and principles supporting the LEED green building programme. Lapsed and not renewed.

The 40-PDU training requirement for the PMP examination has been completed. The PMP credential itself has not been awarded and is not claimed. PMI membership is held separately — see section 1.

Preparatory training for the Intertek Green Belt certification listed above.

Individual module certificates from the MSc coursework in section 2, issued separately for the two modules most relevant to project quality and procurement responsibilities.

In-house lead engineer development programme covering discipline leadership, squad-check and interdiscipline coordination on major capital projects. Certificate available on request.

A confirmation-of-employment letter rather than a service certificate; it states the position held but not a date range.

First professional engagement, entered through the Fluor New Graduate Program — an intake open only to licensed engineers finishing in the top decile of their class. A five-year service award was presented on 24 July 2011. Note the clerical middle initial on this certificate, addressed under Identity of the holder.